Zum Inhalt springen

Windows NT findet beim starten die winsrv.dll nicht.


Sariel

Empfohlene Beiträge

Folgenden Bluescreen bekomme ich beim Start des Rechners zu sehen:

Stop: c0000135 {Unable to Locate DLL}

The dynamic link library winsrv could not be found in the specified path Default Load Path.

Die datei zu ersetzen bringt mir nichts. Habe bei Microsoft aber schon einen Artikel gefunden nur leider komme ich damit nicht ganz klar, weil ich ihn nicht zu 100% verstehe. Und da auf dem PC viele wichtige Programme laufen, würde es sehr lange dauern ihn wieder so zu Konfigurieren. Ich hoffe Ihr könnt mir helfen.

Hier der Artikel von Microsoft:

CAUSE

This error can occur for any of the following reasons:

File_name.dll is missing from the %SystemRoot%\system32 directory.

Your computer is loading the Sermouse.sys file.

If File_Name.dll exists, the software hive may be corrupted and, therefore, cannot load.

RESOLUTION

The method for checking whether File_name.dll exists varies, depending on the file system in use.

For NTFS file systems, install a parallel copy of Windows NT into an unused directory, and then verify that File_name.dll exists in the %SystemRoot%\System32 directory.

For FAT File Systems, an MS-DOS installation disk can be used.

If the file exists, it is possible that the registry software hive has been corrupted. Check the integrity of the software hive by using the following procedure:

WARNING: Using Registry Editor incorrectly can cause serious problems that may require you to reinstall your operating system. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk.

For information about how to edit the registry, view the "Changing Keys And Values" online Help topic in Registry Editor (Regedit.exe) or the "Add and Delete Information in the Registry" and "Edit Registry Data" online Help topics in Regedt32.exe. Note that you should back up the registry before you edit it.

NOTE: In every case tested in which the software hive could not be loaded, the File_name was Winsrv.dll.

From a parallel installation of Windows NT, click Start, and then click Run.

In the dialog box, type Regedt32.

On the toolbar for Registry Editor, click Window, and then click the window with the following name:

HKEY_LOCAL_MACHINE ON LOCAL MACHI

Select the HKEY_LOCAL_MACHINE key in the left pane of the window.

On the menu bar, click Registry, and then click Load Hive.

Browse to %SystemRoot%\System32\config, where %SystemRoot% is the correct installation of Windows NT that you want to check.

Click the file named Software. In Windows NT 4.0, this will be the file named Software that does not have an extension, and has a generic Windows icon next to it, not the file with the Notepad icon. In Windows 3.51, the file name is System, has no extension, and has a generic Windows icon.

The system will prompt for a key-name to use in loading the hive. You can type whatever you prefer in the dialogue box; Work would be a good choice.

The hive is corrupted if you receive the following error message:

Registry Editor could not load the key. The file is not a valid Registry file.

After you have determined the problem, there are several ways to resolve it. The software hive can be restored by making a parallel installation from backup files. It can also be restored from the latest emergency repair disk (ERD), using the procedure outlined below.

NOTE: Windows NT 4.0 requires the Setupdd.sys file to be copied to disk 2 of the Windows NT Setup disks to perform this repair without a CD-ROM. This file can be found in Service Pack 2 or later. For additional information, please see the following article in the Microsoft Knowledge Base:

ARTICLE-ID: 150497

TITLE : How to Repair Windows NT System Files Without a CD-ROM Attached

Start the system with the Windows NT Setup disks.

At the first screen, press R for repair.

Use the arrow keys to move the cursor to Inspect Registry Files, and then press ENTER to select that option. Next, move the cursor to Continue (Perform Selected Tasks) and press ENTER.

Let Windows NT perform the mass storage detection. When prompted, select S to specify additional drivers if your computer requires OEM drivers.

When prompted to do so, insert the emergency repair disk that was originally created for this computer, or press ESC to let Windows NT search for repair information for version 3.51 or version 4.0.

Setup will then ask which registry files should be replaced. Using the arrow keys, move the cursor to Software (Software Information) and press ENTER. Next, move the cursor to Continue (Perform Selected Tasks) and press ENTER.

When finished, restart your computer when Setup prompts you to do so.

Link zu diesem Kommentar
Auf anderen Seiten teilen

Originally posted by palvoelgyi

das Problem hatte ich auch mal. Ich habe dann die NT CD genommen und eine Reparatur gemacht. Danach die Service Packs neu installiert und dann lief der Rechner wieder.

Bei mir nicht. :(

Habe den Rechner jetzt neu installiert.

Aber es wäre nicht schlecht wenn es dafür auch noch andere Lösungen geben würde. :rolleyes:

Link zu diesem Kommentar
Auf anderen Seiten teilen

  • 2 Monate später...

Wenn ich mich recht erinnere, dann wird bei jedem Start die Registry(system.dat, user.dat) als Backup-Kopie angelegt.

Jetzt gibt es da u.a. folgende Möglichkeiten (ungeordnet aufgezählt):

1) Start mit "Last known good configuration"

2) Start im abgesicherten Modus (Himmel, ich kann mich nicht mehr erinnern, ob NT4 sowas hatte ??)

3) Boot mit einer Winternals-ERD-Diskette, die auch NTFS schreiben kann und die system.dat und die user.dat mit den Backups überschreiben.

4) Platte ausbauen und in einem anderen Rechner einbauen, dann starten und von dort aus die Dateien modifizieren.

5) unter W2K hilft manchmal ein simples Chkdsk, vielleicht auch bei NT.

Wo bleibt der Rechner eigentlich genau stehen ?

Kurz nach "ntdetect" ?

Während des normalen Bluescreens ?

Mehr Information wäre nicht schlecht.

Link zu diesem Kommentar
Auf anderen Seiten teilen

1) Start mit "Last known good configuration"

Geht net, gibts net.......

2) Start im abgesicherten Modus (Himmel, ich kann mich nicht mehr erinnern, ob NT4 sowas hatte ??)

NT hat sowas, aber bootet trotzdem net....

3) Boot mit einer Winternals-ERD-Diskette, die auch NTFS schreiben kann und die system.dat und die user.dat mit den Backups überschreiben.

Brach ich nich weil ich das gemacht hab!:

4) Platte ausbauen und in einem anderen Rechner einbauen, dann starten und von dort aus die Dateien modifizieren.

5) unter W2K hilft manchmal ein simples Chkdsk, vielleicht auch bei NT.

Hab ich auch schon.....

Oki, die meldung kommt bei dem netten blauen Bildschirm wo dann immer die Windows Version, Speicher etc steht

die Fehlermeldung steht ja oben schon....

hab schon den system32 ordner von ner anderen NT installation rüberkopiert aber geht immenochnix

mfg cjw

Link zu diesem Kommentar
Auf anderen Seiten teilen

Originally posted by CJW

Geht net, gibts net.......

Also, wenn meine Denkmurmel noch halbwegs läuft, dann kommt der "Drücken Sie die Leertaste für die letzte gesicherte Konfiguration" unmittelbar VOR dem Bluescreen mit den Windows Anzeigen (Build 13xx, SP6 etc.)

Das würde ich dennoch versuchen.

die Fehlermeldung steht ja oben schon....

hab schon den system32 ordner von ner anderen NT installation rüberkopiert aber geht immenochnix

Da ist ziemlich wahrscheinlich auch die Registry im Orkus und braucht "Hilfe". Da muß vermutlich nur ein Key gelöscht werden und gut ist's.

=> die system.dat und user.dat wiederherstellen.

Link zu diesem Kommentar
Auf anderen Seiten teilen

So natürlich gar nicht. ;)

Das die Registry kaputt ist war ein Statement.

Jetzt mußt Du alles suchen was system.dat und ähnlich klingend auf der Platte liegt.

Vermutlich gibt es Datei, die system.da_ oder system.bak etc. heißt und fast identisch groß mit der system.dat ist.

Dann benennest Du die system.dat um und dann die andere Datei zu system.dat.

Das gleiche tust Du mit der user.dat.

Danach baust Du die HDD wieder in den originären Rechner ein und dann sollte er ordentlich booten.

Link zu diesem Kommentar
Auf anderen Seiten teilen

Dein Kommentar

Du kannst jetzt schreiben und Dich später registrieren. Wenn Du ein Konto hast, melde Dich jetzt an, um unter Deinem Benutzernamen zu schreiben.

Gast
Auf dieses Thema antworten...

×   Du hast formatierten Text eingefügt.   Formatierung wiederherstellen

  Nur 75 Emojis sind erlaubt.

×   Dein Link wurde automatisch eingebettet.   Einbetten rückgängig machen und als Link darstellen

×   Dein vorheriger Inhalt wurde wiederhergestellt.   Editor leeren

×   Du kannst Bilder nicht direkt einfügen. Lade Bilder hoch oder lade sie von einer URL.

Fachinformatiker.de, 2024 by SE Internet Services

fidelogo_small.png

Schicke uns eine Nachricht!

Fachinformatiker.de ist die größte IT-Community
rund um Ausbildung, Job, Weiterbildung für IT-Fachkräfte.

Fachinformatiker.de App

Download on the App Store
Get it on Google Play

Kontakt

Hier werben?
Oder sende eine E-Mail an

Social media u. feeds

Jobboard für Fachinformatiker und IT-Fachkräfte

×
×
  • Neu erstellen...